Moduł 8 wyjść binarnych systemu XI/ON ECO
- szt.
- Rabat: -313,84 zł (40 %)
- (Rabat brutto: -386,02 zł (40 %))
- Cena brutto: 579,04 zł / szt. 470,76 zł / szt.
Moduł 8 wyjść binarnych, wersja ECO XNE-8DO-24VDC-0.5A-P
Program
I/O modules | |||
Digital output modules | |||
XNE Slice module | |||
Description | 8 Digital output, 24 V DC/0.5 A Positive switching | ||
Information relevant for export to North America Product StandardsIEC/EN 60947-4-1; UL 508; CSA-C22.2 No. 14-05; CE marking UL File No.E29184 UL CCNNKCR CSA File No.012528 CSA Class No.3211-03 NA CertificationUL Listed, CSA certified |
Approbationen
|
General | |||
Standards | EN 61000-6-2 EN 61000-6-4 EN 61131-2 | ||
Potential isolation | Yes, through optocoupler | ||
Ambient temperature | °C | 0 - +55 | |
Storage | °C | -25 - +85 | |
Relative humidity | % | 5 - 95 (indoor), level RH-2, non-condensing (at 45 °C storage) | |
Schadgas | ppm | SO2: 10 (rel. Feuchte < 75 %, keine Kondensation) H2S: 1.0 (rel. Feuchte < 75 %, keine Kondensation) | |
Vibrationsfestigkeit, Einsatzbedingungen | gemäß IEC 60068-2-6 | ||
Mechanical shock resistance | g | gemäß IEC 60068-2-27 | |
Continuous shock resistance (IEC/EN 60068-2-29) | According to IEC 60068-2-29 | ||
Drop and topple | According to IEC 60068-2-31, free fall according to IEC 60068-2-32 | ||
Protection type | IP20 | ||
Electromagnetic compatibility (EMC) | |||
ESD | EN 61100-4-2 | ||
Electromagnetic fields | EN 61100-4-2 | ||
Burst | EN 61100-4-4 | ||
Surge | EN 61100-4-5 | ||
HF unsymmetric | EN 61100-4-6 | ||
Emitted interference (radiated, high frequency) | EN 55016-2-3 | ||
Spannungsvariationen | EN 61131-2 | ||
Type test | to EN 61131-2 | ||
Approvals | CE, cUL (ggf. in Bearbeitung) | ||
Other technical data (sheet catalogue) | Technical Data | ||
Terminations | |||
Rated data | nach VDE 0611 Teil 1/8.92/ IEC/EN 60947-7-1 | ||
Connection design in TOP direction | Push-In Federzugklemmen | ||
Stripping length | mm | 8 | |
Clamping range | max. 0.14 - 1.5 mm2 | ||
Connectable conductors | |||
"e" eindrähtig H 07V-U | mm2 | 0.25 - 1.5 | |
"f" feindrähtig H 07V-K | mm2 | 0.25 - 1.5 | |
"f" mit Aderendhülsen ohne Kunstoffkragen nach DIN 46228-1 (Aderendhülsen gasdicht festgedrückt) | mm2 | 0.25 - 1.5 | |
"f" mit Aderendhülsen mit Kunstoffkragen nach DIN 46228-1 (Aderendhülsen gasdicht festgedrückt) | mm2 | 0.25 - 0.75 | |
Gauge pin IEC/EN 60947-1 | A1 | ||
Digital output modules | |||
Channels | Number | 8 | |
Rated voltage through supply terminal | UL | 24 V DC | |
Rated current consumption from the supply terminal (at load current = 0 mA) | IL | mA | 3 |
Rated current consumption from module bus | IMB | mA | 15 |
Power loss | W | Normally 1.5 | |
Output voltage | |||
High level | UH⁄UA | > UL- 1 V DC | |
Output current | A | ||
High level (rated value) | IH | 0.5 A | |
High level (permissible range) | IH | A | < 1.0 |
Delay on signal change and resistive load | |||
from Low to High level | µs | 300 | |
From High to Low signal | µs | 300 | |
Utilization factor | % | g | 100 |
Can be connected | Resistive loads Inductive loads Lamp loads | ||
Resistive load | Ω | 48 | |
Inductive load | h | gemäß DC13 nach IEC 60947-5-1 | |
Lamp load | RLL | W | 6 |
Switching frequency | |||
With resistive load | f | Hz | 100 |
bei induktiver Last | gemäß DC13 nach IEC 60947-5-1 | ||
with lamp load | Hz | 10 | |
Ausgang nach EN 61131-2 | short-circuit proof | ||
Reset after short-circuit rectified | Ii | Automatic | |
Notes | |||
The supply terminal (UL) provides power for the module electronics and for the consumers at the outputs. The total current required for each module consists of the sum of all partial currents. Part of the XI/ON module’s electronics is supplied with module bus voltage (5 V DC), the other part through the supply terminal (UL). To increase the maximum output current to up to 1 A, two outputs can be connected in parallel. |
Opis pochodzi ze strony www.moeller.net .